Flexcharge SA120VAC AC Surge Arrester 120 Volts
Flexcharge SA120VAC | AC Surge Arrester 120 Volts (Multiple Values) Flexcharge AC Surge Arrester 120 Volts Model: SA120VAC US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page The following is copyrighted by SES Flexcharge. Near by lighting strikes, switches, relays, and static electricity can all cause damaging spikes and surges in your electrical system on the DC and AC sides. The Flexcharge Surge Arresters are completely transparent to the system until the voltage on the system reaches the breakdown voltage of the unit. Normally, high voltage spikes that are dissipated by the surge arrester will not damage the surge arrester and it will continue to protect your circuit. Using a triangulated spark gap circuit, the Flexcharge surge arresters will dissipate high voltage spikes to ground before the voltage in the system reaches extreme levels. Manufactured with UL approved components, each model is designed for specific voltage protection ranges on both DC and AC systems. Install the unit near the device that you want to protect. Some systems will require more than one unit for full protection. Model # Description System Voltage Breakdown V SA1224DC DC Surge Arrester 12-24 60-90 SA3648DC DC Surge Arrester 36-48 116-174 SA120VAC AC Surge Arrester 120 225 Use the appropriate surge arrester for the system voltage and AC or DC circuit. Installation All three wires must be connected properly for the surge arrester to operate. Follow the wiring color code on the unit label. Install the unit next to the device you want to protect. For example on the AC side of an inverter, install the surge arrester on the AC output terminals of the inverter. For solar and wind systems install a DC surge arrester just before the charge controller. In some systems that have above ground wires between the solar or wind system and the batteries, install another surge arrester near the solar or wind system. The Green (earth ground) wire must go directly to a ground rod or ground plate. If you have multiple ground rods be sure to run a common wire to all the ground rods so they are tied together electrically. This is very important to prevent a ground loop. Solder all wire to wire connections. The surge arrestor can withstand multiple high voltage surges but prolonged high voltage above the ratied limit can cause a failure. If the case become hot or warped it has failed. If this happens you must remove it from the system and replace the unit. Hurricane Wind Power Build News Magazine Best Off Grid 2016Product Supplier Renewable Energy UP TO 50% DISCOUNTSTOP BRANDSPaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other itemsThank you for visiting our Ebay store!(Multiple Values) Flexcharge AC Surge Arrester 120 Volts Model: SA120VAC US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page: [http://www.flexcharge.com/Where-to-buy.html] (http://www.flexcharge.com/Where-to-buy.html) The following is copyrighted by SES Flexcharge. Near by lighting strikes, switches, relays, and static electricity can all cause damaging spikes and surges in your electrical system on the DC and AC sides. The Flexcharge Surge Arresters are completely transparent to the system until the voltage on the system reaches the breakdown voltage of the unit. Normally, high voltage spikes that are dissipated by the surge arrester will not damage the surge arrester and it will continue to protect your circuit. Using a triangulated spark gap circuit, the Flexcharge surge arresters will dissipate high voltage spikes to ground before the voltage in the system reaches extreme levels. Manufactured with UL approved components, each model is designed for specific voltage protection ranges on both DC and AC systems. Install the unit near the device that you want to protect. Some systems will require more than one unit for full protection. Model # Description System Voltage Breakdown V SA1224DC DC Surge Arrester 12-24 60-90 SA3648DC DC Surge Arrester 36-48 116-174 SA120VAC AC Surge Arrester 120 225 Use the appropriate surge arrester for the system voltage and AC or DC circuit. Installation All three wires must be connected properly for the surge arrester to operate. Follow the wiring color code on the unit label. Install the unit next to the device you want to protect. For example on the AC side of an inverter, install the surge arrester on the AC output terminals of the inverter. For solar and wind systems install a DC surge arrester just before the charge controller. In some systems that have above ground wires between the solar or wind system and the batteries, install another surge arrester near the solar or wind system. The Green (earth ground) wire must go directly to a ground rod or ground plate. If you have multiple ground rods be sure to run a common wire to all the ground rods so they are tied together electrically. This is very important to prevent a ground loop. Solder all wire to wire connections. The surge arrestor can withstand multiple high voltage surges but prolonged high voltage above the ratied limit can cause a failure. If the case become hot or warped it has failed. If this happens you must remove it from the system and replace the unit. [FREE! Sellers: Add a FREE map to your listings. FREE!] (http://newage.mystoremaps.com/echo/tagLine?sid=cea073c8-fc6f-494f-9ca5-610e8850a127&tid=2) Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Flexcharge SA120VAC | AC Surge Arrester 120 Volts (Multiple Values) Flexcharge AC Surge Arrester 120 Volts Model: SA120VAC US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page: http://www.flexcharge.com/Where-to-buy.html The following is copyrighted by SES Flexcharge. Near by lighting strikes, switches, relays, and static electricity can all cause damaging spikes and surges in your electrical system on the DC and AC sides. The Flexcharge Surge Arresters are completely transparent to the system until the voltage on the system reaches the breakdown voltage of the unit. Normally, high voltage spikes that are dissipated by the surge arrester will not damage the surge arrester and it will continue to protect your circuit. Using a triangulated spark gap circuit, the Flexcharge surge arresters will dissipate high voltage spikes to ground before the voltage in the system reaches extreme levels. Manufactured with UL approved components, each model is designed for specific voltage protection ranges on both DC and AC systems. Install the unit near the device that you want to protect. Some systems will require more than one unit for full protection. Model # Description System Voltage Breakdown V SA1224DC DC Surge Arrester 12-24 60-90 SA3648DC DC Surge Arrester 36-48 116-174 SA120VAC AC Surge Arrester 120 225 Use the appropriate surge arrester for the system voltage and AC or DC circuit. Installation All three wires must be connected properly for the surge arrester to operate. Follow the wiring color code on the unit label. Install the unit next to the device you want to protect. For example on the AC side of an inverter, install the surge arrester on the AC output terminals of the inverter. For solar and wind systems install a DC surge arrester just before the charge controller. In some systems that have above ground wires between the solar or wind system and the batteries, install another surge arrester near the solar or wind system. The Green (earth ground) wire must go directly to a ground rod or ground plate. If you have multiple ground rods be sure to run a common wire to all the ground rods so they are tied together electrically. This is very important to prevent a ground loop. Solder all wire to wire connections. The surge arrestor can withstand multiple high voltage surges but prolonged high voltage above the ratied limit can cause a failure. If the case become hot or warped it has failed. If this happens you must remove it from the system and replace the unit. FREE! Sellers: Add a FREE map to your listings. FREE! Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Hurricane Wind Power Build News Magazine Best Off Grid 2016Renewable Energy Product Supplier UP TO 50% DISCOUNTSTOP BRANDSSee our other itemsPayment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. Thank you for visiting our Ebay store!
Specifications
| Return Shipping Will Be Paid By | Seller |
| All Returns Accepted | Returns Accepted |
| Item Must Be Returned Within | 30 Days |
| Brand | Flexcharge |
| Model | SA120VAC |
| Country/Region Of Manufacture | United States |
| MPN | SA120VAC |
Flexcharge SA120VAC | AC Surge Arrester 120 Volts (Multiple Values) Flexcharge AC Surge Arrester 120 Volts Model: SA120VAC US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page The following is copyrighted by SES Flexcharge. Near by lighting strikes, switches, relays, and static electricity can all cause damaging spikes and surges in your electrical system on the DC and AC sides. The Flexcharge Surge Arresters are completely transparent to the system until the voltage on the system reaches the breakdown voltage of the unit. Normally, high voltage spikes that are dissipated by the surge arrester will not damage the surge arrester and it will continue to protect your circuit. Using a triangulated spark gap circuit, the Flexcharge surge arresters will dissipate high voltage spikes to ground before the voltage in the system reaches extreme levels. Manufactured with UL approved components, each model is designed for specific voltage protection ranges on both DC and AC systems. Install the unit near the device that you want to protect. Some systems will require more than one unit for full protection. Model # Description System Voltage Breakdown V SA1224DC DC Surge Arrester 12-24 60-90 SA3648DC DC Surge Arrester 36-48 116-174 SA120VAC AC Surge Arrester 120 225 Use the appropriate surge arrester for the system voltage and AC or DC circuit. Installation All three wires must be connected properly for the surge arrester to operate. Follow the wiring color code on the unit label. Install the unit next to the device you want to protect. For example on the AC side of an inverter, install the surge arrester on the AC output terminals of the inverter. For solar and wind systems install a DC surge arrester just before the charge controller. In some systems that have above ground wires between the solar or wind system and the batteries, install another surge arrester near the solar or wind system. The Green (earth ground) wire must go directly to a ground rod or ground plate. If you have multiple ground rods be sure to run a common wire to all the ground rods so they are tied together electrically. This is very important to prevent a ground loop. Solder all wire to wire connections. The surge arrestor can withstand multiple high voltage surges but prolonged high voltage above the ratied limit can cause a failure. If the case become hot or warped it has failed. If this happens you must remove it from the system and replace the unit. Hurricane Wind Power Build News Magazine Best Off Grid 2016Product Supplier Renewable Energy UP TO 50% DISCOUNTSTOP BRANDSPaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other itemsThank you for visiting our Ebay store!(Multiple Values) Flexcharge AC Surge Arrester 120 Volts Model: SA120VAC US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page: [http://www.flexcharge.com/Where-to-buy.html] (http://www.flexcharge.com/Where-to-buy.html) The following is copyrighted by SES Flexcharge. Near by lighting strikes, switches, relays, and static electricity can all cause damaging spikes and surges in your electrical system on the DC and AC sides. The Flexcharge Surge Arresters are completely transparent to the system until the voltage on the system reaches the breakdown voltage of the unit. Normally, high voltage spikes that are dissipated by the surge arrester will not damage the surge arrester and it will continue to protect your circuit. Using a triangulated spark gap circuit, the Flexcharge surge arresters will dissipate high voltage spikes to ground before the voltage in the system reaches extreme levels. Manufactured with UL approved components, each model is designed for specific voltage protection ranges on both DC and AC systems. Install the unit near the device that you want to protect. Some systems will require more than one unit for full protection. Model # Description System Voltage Breakdown V SA1224DC DC Surge Arrester 12-24 60-90 SA3648DC DC Surge Arrester 36-48 116-174 SA120VAC AC Surge Arrester 120 225 Use the appropriate surge arrester for the system voltage and AC or DC circuit. Installation All three wires must be connected properly for the surge arrester to operate. Follow the wiring color code on the unit label. Install the unit next to the device you want to protect. For example on the AC side of an inverter, install the surge arrester on the AC output terminals of the inverter. For solar and wind systems install a DC surge arrester just before the charge controller. In some systems that have above ground wires between the solar or wind system and the batteries, install another surge arrester near the solar or wind system. The Green (earth ground) wire must go directly to a ground rod or ground plate. If you have multiple ground rods be sure to run a common wire to all the ground rods so they are tied together electrically. This is very important to prevent a ground loop. Solder all wire to wire connections. The surge arrestor can withstand multiple high voltage surges but prolonged high voltage above the ratied limit can cause a failure. If the case become hot or warped it has failed. If this happens you must remove it from the system and replace the unit. [FREE! Sellers: Add a FREE map to your listings. FREE!] (http://newage.mystoremaps.com/echo/tagLine?sid=cea073c8-fc6f-494f-9ca5-610e8850a127&tid=2) Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Flexcharge SA120VAC | AC Surge Arrester 120 Volts (Multiple Values) Flexcharge AC Surge Arrester 120 Volts Model: SA120VAC US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page: http://www.flexcharge.com/Where-to-buy.html The following is copyrighted by SES Flexcharge. Near by lighting strikes, switches, relays, and static electricity can all cause damaging spikes and surges in your electrical system on the DC and AC sides. The Flexcharge Surge Arresters are completely transparent to the system until the voltage on the system reaches the breakdown voltage of the unit. Normally, high voltage spikes that are dissipated by the surge arrester will not damage the surge arrester and it will continue to protect your circuit. Using a triangulated spark gap circuit, the Flexcharge surge arresters will dissipate high voltage spikes to ground before the voltage in the system reaches extreme levels. Manufactured with UL approved components, each model is designed for specific voltage protection ranges on both DC and AC systems. Install the unit near the device that you want to protect. Some systems will require more than one unit for full protection. Model # Description System Voltage Breakdown V SA1224DC DC Surge Arrester 12-24 60-90 SA3648DC DC Surge Arrester 36-48 116-174 SA120VAC AC Surge Arrester 120 225 Use the appropriate surge arrester for the system voltage and AC or DC circuit. Installation All three wires must be connected properly for the surge arrester to operate. Follow the wiring color code on the unit label. Install the unit next to the device you want to protect. For example on the AC side of an inverter, install the surge arrester on the AC output terminals of the inverter. For solar and wind systems install a DC surge arrester just before the charge controller. In some systems that have above ground wires between the solar or wind system and the batteries, install another surge arrester near the solar or wind system. The Green (earth ground) wire must go directly to a ground rod or ground plate. If you have multiple ground rods be sure to run a common wire to all the ground rods so they are tied together electrically. This is very important to prevent a ground loop. Solder all wire to wire connections. The surge arrestor can withstand multiple high voltage surges but prolonged high voltage above the ratied limit can cause a failure. If the case become hot or warped it has failed. If this happens you must remove it from the system and replace the unit. FREE! Sellers: Add a FREE map to your listings. FREE! Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application Hurricane Wind Power Build News Magazine Best Off Grid 2016Renewable Energy Product Supplier UP TO 50% DISCOUNTSTOP BRANDSSee our other itemsPayment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. Thank you for visiting our Ebay store!
Related Items
