Case Ingersoll Loader Custom Axle Pin Extreme Duty Upgrade Kit
**FREE SHIPPING** For Case Ingersoll Loader Models. Extreme Duty Front Axle Pin Custom Upgrade Kit Modification Improvement. Major improvement Modification for Case Ingersoll 644, 646, 648, 6018, 6020 loaders and backhoes. This Pin is for Factory purpose built loader models. Check Our store for the upgraded garden tractor model pin options. Replaces and improved design over OEM Part numbers C45082, C43847, C26759, C19018, C26760, C22278, 2-19-35 This is our in house designed axle pin kit for your loader. It not only blows the poor designed expensive OEM pins away but it also solves the clearance issues with the common aftermarket pins being sold for loaders out there. "what clearance issues?" If you have a aftermarket loader pin there is a good chance it is at a minimum scratching your tie rod but likely bending/bowing it too on "full turns” all the way in either direction. For roughly the same price of the undesirable OEM pin you can have this far superior designed pin, with better materials and lots more work and machining into it that will be a permanent problem solver and upgrade. **We now have a grease fitting added to the back threaded cap for a few reasons, Extra lube point, also you can use grease pressure to remove the pin if or when needed by pumping grease in rear fitting. Or if you prefer remove the rear fitting and push the pin out with a mall punch. (note some pictures show the earlier pins with only 1 grease fitting)** Here is a link to our install and Explanation video Here https://youtu.be/kA5Rw8ndHbY?si=huk3UyZ7ty9jORLw We sell out often of our pins be sure to check back or contact us. As we will have more in on a regular schedule. Our kit ALSO gives you many times more load-bearing surface, it also allows you to re-center your axle on severely worn-out machines, it can also correct worn out or oblong holes in the axle plate brackets that is attached to your frame that sandwiches the axle IF you choose to also weld this pins collars. Though welding is not required to install this pin and get the benefits, but it is a additional benefit if you so CHOOSE. These holes commonly get worn out, especially if the factory axle pin has been used for a long time and is continually used and not greased. And this can be very dangerous, limits performance and wears your machine fast. You can now get all these benefits plus the heavy-duty pin and the ability to clamp all the play out of your axle. And if choosing to weld the two provided collar pieces to the front and back of the axle bracket you get an added benefit Fast and simple to install. Hardware included is grade 8. You also get One custom weldable collar WITH grease fitting, One machined, recessed and threaded clamping weldable end cap, one long heavy-duty axle pin with grease channels and rings, One very large 1/4 inch thick clamping washer, A flat washers and one bolt to complete the installation. Installation is very simple and fast. AXLES SHOULD HAVE ZERO FORE AND AFT MOVEMENT AS WELL AS ZERO SIDE-TO-SIDE MOVEMENT AND NO FRONT OR BACK ROLL OR UP AND DOWN. The only movement should be pivoting on the pin for side hill operation or on uneven terrain. This pin fits ALL 600 series tractors, 6000 series LOADER tractors, Do Not Forget To Replace Your Rod Ends, on the drag link, tie rod and power steering cylinder. Check how many right hand and left hand ends YOUR machine HAS. Here is the link to them in our store on our website SHOP TIP: Pay attention to where you want your grease fitting and line it up with main grease channel cut in pin on install.Collars do not need to be fully welded if you do not want to. If welding They simply need three or four small welds each to center and hold them in place. Refer to our "LOADER" axle pin video for more information. AXLES SHOULD HAVE ZERO FORE AND AFT MOVEMENT AS WELL AS ZERO SIDE-TO-SIDE MOVEMENT AND NO FRONT OR BACK ROLL. The only movement should be pivoting on the pin for side hill operation or on uneven terrain. **WE SUPPORT AMERICA, SMALL BUSINESSES, MILITARY/VETERANS WHENEVER AND WHEREVER WE CAN!!! WEBSITE FOR MORE INFO ABOUT US AT caseingersolltractors.com , Follow us on Face Book at Case Ingersoll Garden Tractors Northeast. And for lots of info and tractors in action, be sure to watch and SUBSCRIBE to our You Tube channel at Case Ingersoll Tractors Northeast THANK YOU FOR YOUR SUPPORT OF SMALL USA BUSINESSES. REACH OUT FOR ANY QUESTIONS. GENERAL DISCLAIMER/TERMS/CONDITIONS FOR NEW AND USED ITEMS SHIPPING AND PICK UP POLICY. Almost all times we have multiple kits made up and on the shelf and ship them out within 1 business day. But we also offer for sale the kits locally at our shop and on our web site to our customers as well as we install them for customers, so we try to keep the inventory for online sales as accurate as we can. But sometimes there is an overlap. So if the rare time a overlap happens we have to make/put the new kits together and then ship them out. Most times this takes UP TO 2 to 4 business days. We just wanted to be upfront about that. You can message us to check current inventory. PLEASE CHECK ALL PART AND MODEL NUMBERS, INFO AND PHOTOS BEFORE BUYING AND FEEL FREE TO ASK QUESTIONS. It is up to you to make sure this fits YOUR tractor before purchasing,THANK YOU. LOOK OVER PHOTOS. What is pictured and the main item in picture (not background) is what you get, Ask If I can help you in any way. I OR WE THE SELLER accepts no responsibility or liability for the use of, missuses, abuse, resale of any item purchased. I THE SELLER shall not be responsible for failure of equipment nor complications arising from failure caused or not cause by item sold. Nor any damage or injuries caused by item sold or it's correct or incorrect installation and or use by BUYER or those associated with the BUYER. Once the product/products/ leave our possession I THE SELLER accepts zero, no responsibility or liability for the use of, misuses, abuse, resale of any item purchased. I THE SELLER shall not be responsible for failure or use of equipment nor complications arising from failure caused or not cause by items sold. Nor am held liable for any damage or injuries caused by items sold or items correctly or incorrectly installed and or used by anyone including BUYER and or installer or those associated with the BUYER or installers. BUYER accepts all this with the purchase as well as ALL AND ANY responsibility and liability as soon as they take possession of item in person or via shipment. It is solely the purchaser’s responsibility to choose qualified trained professionals for correct and safe product installation and All items/products/goods are purchased by the BUYER are "AS IS" condition, and I THE SELLER make no representation or warranty, expressed, or implied. BUYER excepts all this with purchase as well as ALL AND ANY responsibility and liability as soon as they take possession of item. It is your duty to make sure the item will work for your needs and or fit BEFORE YOU PURCHASE. So please feel free to ask questions if you need to and we will help to the best we can and THANK YOU. If you have any issues please reach out and contact me. I have lots of Case Ingersoll parts and items, so let me know what you may need and If I have it we can make a listing so it can be purchased. Thank You
Specifications
| All Returns Accepted | ReturnsNotAccepted |
| Brand | Case Ingersoll |
| Compatible Brand | Case |
| Type | PIN |
| Material | Steel |
| Country/Region Of Manufacture | United States |
**FREE SHIPPING** For Case Ingersoll Loader Models. Extreme Duty Front Axle Pin Custom Upgrade Kit Modification Improvement. Major improvement Modification for Case Ingersoll 644, 646, 648, 6018, 6020 loaders and backhoes. This Pin is for Factory purpose built loader models. Check Our store for the upgraded garden tractor model pin options. Replaces and improved design over OEM Part numbers C45082, C43847, C26759, C19018, C26760, C22278, 2-19-35 This is our in house designed axle pin kit for your loader. It not only blows the poor designed expensive OEM pins away but it also solves the clearance issues with the common aftermarket pins being sold for loaders out there. "what clearance issues?" If you have a aftermarket loader pin there is a good chance it is at a minimum scratching your tie rod but likely bending/bowing it too on "full turns” all the way in either direction. For roughly the same price of the undesirable OEM pin you can have this far superior designed pin, with better materials and lots more work and machining into it that will be a permanent problem solver and upgrade. **We now have a grease fitting added to the back threaded cap for a few reasons, Extra lube point, also you can use grease pressure to remove the pin if or when needed by pumping grease in rear fitting. Or if you prefer remove the rear fitting and push the pin out with a mall punch. (note some pictures show the earlier pins with only 1 grease fitting)** Here is a link to our install and Explanation video Here https://youtu.be/kA5Rw8ndHbY?si=huk3UyZ7ty9jORLw We sell out often of our pins be sure to check back or contact us. As we will have more in on a regular schedule. Our kit ALSO gives you many times more load-bearing surface, it also allows you to re-center your axle on severely worn-out machines, it can also correct worn out or oblong holes in the axle plate brackets that is attached to your frame that sandwiches the axle IF you choose to also weld this pins collars. Though welding is not required to install this pin and get the benefits, but it is a additional benefit if you so CHOOSE. These holes commonly get worn out, especially if the factory axle pin has been used for a long time and is continually used and not greased. And this can be very dangerous, limits performance and wears your machine fast. You can now get all these benefits plus the heavy-duty pin and the ability to clamp all the play out of your axle. And if choosing to weld the two provided collar pieces to the front and back of the axle bracket you get an added benefit Fast and simple to install. Hardware included is grade 8. You also get One custom weldable collar WITH grease fitting, One machined, recessed and threaded clamping weldable end cap, one long heavy-duty axle pin with grease channels and rings, One very large 1/4 inch thick clamping washer, A flat washers and one bolt to complete the installation. Installation is very simple and fast. AXLES SHOULD HAVE ZERO FORE AND AFT MOVEMENT AS WELL AS ZERO SIDE-TO-SIDE MOVEMENT AND NO FRONT OR BACK ROLL OR UP AND DOWN. The only movement should be pivoting on the pin for side hill operation or on uneven terrain. This pin fits ALL 600 series tractors, 6000 series LOADER tractors, Do Not Forget To Replace Your Rod Ends, on the drag link, tie rod and power steering cylinder. Check how many right hand and left hand ends YOUR machine HAS. Here is the link to them in our store on our website SHOP TIP: Pay attention to where you want your grease fitting and line it up with main grease channel cut in pin on install.Collars do not need to be fully welded if you do not want to. If welding They simply need three or four small welds each to center and hold them in place. Refer to our "LOADER" axle pin video for more information. AXLES SHOULD HAVE ZERO FORE AND AFT MOVEMENT AS WELL AS ZERO SIDE-TO-SIDE MOVEMENT AND NO FRONT OR BACK ROLL. The only movement should be pivoting on the pin for side hill operation or on uneven terrain. **WE SUPPORT AMERICA, SMALL BUSINESSES, MILITARY/VETERANS WHENEVER AND WHEREVER WE CAN!!! WEBSITE FOR MORE INFO ABOUT US AT caseingersolltractors.com , Follow us on Face Book at Case Ingersoll Garden Tractors Northeast. And for lots of info and tractors in action, be sure to watch and SUBSCRIBE to our You Tube channel at Case Ingersoll Tractors Northeast THANK YOU FOR YOUR SUPPORT OF SMALL USA BUSINESSES. REACH OUT FOR ANY QUESTIONS. GENERAL DISCLAIMER/TERMS/CONDITIONS FOR NEW AND USED ITEMS SHIPPING AND PICK UP POLICY. Almost all times we have multiple kits made up and on the shelf and ship them out within 1 business day. But we also offer for sale the kits locally at our shop and on our web site to our customers as well as we install them for customers, so we try to keep the inventory for online sales as accurate as we can. But sometimes there is an overlap. So if the rare time a overlap happens we have to make/put the new kits together and then ship them out. Most times this takes UP TO 2 to 4 business days. We just wanted to be upfront about that. You can message us to check current inventory. PLEASE CHECK ALL PART AND MODEL NUMBERS, INFO AND PHOTOS BEFORE BUYING AND FEEL FREE TO ASK QUESTIONS. It is up to you to make sure this fits YOUR tractor before purchasing,THANK YOU. LOOK OVER PHOTOS. What is pictured and the main item in picture (not background) is what you get, Ask If I can help you in any way. I OR WE THE SELLER accepts no responsibility or liability for the use of, missuses, abuse, resale of any item purchased. I THE SELLER shall not be responsible for failure of equipment nor complications arising from failure caused or not cause by item sold. Nor any damage or injuries caused by item sold or it's correct or incorrect installation and or use by BUYER or those associated with the BUYER. Once the product/products/ leave our possession I THE SELLER accepts zero, no responsibility or liability for the use of, misuses, abuse, resale of any item purchased. I THE SELLER shall not be responsible for failure or use of equipment nor complications arising from failure caused or not cause by items sold. Nor am held liable for any damage or injuries caused by items sold or items correctly or incorrectly installed and or used by anyone including BUYER and or installer or those associated with the BUYER or installers. BUYER accepts all this with the purchase as well as ALL AND ANY responsibility and liability as soon as they take possession of item in person or via shipment. It is solely the purchaser’s responsibility to choose qualified trained professionals for correct and safe product installation and All items/products/goods are purchased by the BUYER are "AS IS" condition, and I THE SELLER make no representation or warranty, expressed, or implied. BUYER excepts all this with purchase as well as ALL AND ANY responsibility and liability as soon as they take possession of item. It is your duty to make sure the item will work for your needs and or fit BEFORE YOU PURCHASE. So please feel free to ask questions if you need to and we will help to the best we can and THANK YOU. If you have any issues please reach out and contact me. I have lots of Case Ingersoll parts and items, so let me know what you may need and If I have it we can make a listing so it can be purchased. Thank You
Related Items
